Hop78

There is a low fuel light, it should come on as it hits the reserve, mine was then it started to come on occasionally, but now doesn't come on at all, I haven't figured out what the problem is.

I ended up stripping the iacv and fitv off and cleaned them with carb cleaner along with the throttle body, also the wires were the wrong way round on the iacv plug and I had to run a new wire from the iacv to the ecu, this sorted the problem out, hope this helps sort you out, I've figured out it pointless asking for any help on here for anything apart from what wheels or spoiler to put on!

ive just swapped out my d14z4 and fitted d16y2, the problem i am having is the injector closest to the air filter is gushing out and the other 3 injectors pulse as they should, tried fitting the ecu from the d14 and the injectors operate correctly. i presumed it must of the been a duff ecu that came with the engine, so i bought a p28 and the problem is still there. Tried swapping the injectors around and it doesnt make any difference. the problem stays where it is and doesnt follow the injector. The engine is obd2a and is converted with an ecu harness to obd1 at the ecu, Is there any wiring that needs changed for the injectors? this has already resulted in the head and the sump getting filled with fuel and choked the exhaust and cat up.

I need to repin an Iacv after an engine swap from d14z4 to d16y2 it's obd2a with an conversation harness to obd1. I've hard wired the vtec which is working, but I'm getting an error code 14 IAC (EACV) - idle air control valve. The iacv has been swapped to a two wire one and I presume it needs repining on the harness, but I don't know which I don't know which pin to move to from the obd2a harness to the obd1 harness? Any help would be appreciated as this is really starting to pee me off now 😡 Cheers

That already fits, I currently have a d16z6 inlet manifold fitted to the d14z4, it's just the wireing, wasn't sure if the engine loom will click directly in to the mb dash loom, struggling to find any info, seems like no one has done this on an mb before 😡

Can anyone tell me if the d16z6 engine loom will plug into a mb2 d14z4 or will it need modified or an adaptor harness fitted???

Can anyone tell me if the d16z6 engine loom will clip directly into the d14z4, wasn't sure if all I would need is the odb2a - odb1 jumper harness and wire the vtec in directly or if there is any other wiring to do? Just trying to cover all possibilities before I do the swap and then get stuck with it not starting. Cheers

Do you know if the d16z6 engine loom will clip directly in, wasn't sure if all I would need is the odb2a - odb1 jumper harness and wire the vtec in directly or if there is any other wiring to do? Just trying to cover all possibilities before I do the swap and then get stuck with it not starting.

Cheers for the help mate ðŸ‘

It's cheaper doing the engine swap, by the time you d**k about doing the head gasket and timing you could buy a b18 conversion, I've got the d16z6 engine and the ecu to suit, think the only thing I will have to do is hardware the vtec to the ecu, I dont suppose anyone knows which pin the vtec wire's to on the ecu?

Is the above ecu off an mb2 a obd2a or b? Need a harness for and engine conversation? Cheers

I'm hoping, just wasn't sure if there was anything else apart from the vtec wire I would have to do

Can anyone give me information on doing a d16z6 swap to an mb2, it's getting a full swap with a p28 ecu and then the vtec wired indirectly to the ecu, is there anything else I need or any problems I can expect to come across? Cheers

Can any one advise the location of the central locking module on an mb2, I presume it's in the same place as most mb's but can't actually find anything for it on the net? Cheers

Looks like that's the stuff I'm after, but I'm English and can't read that. Cheers for the link though