Leaderboard

Sorry for the delay, thanks Sir Paperbag/ Patrick ! I already have bright halogen H4s fitted, Philips, extreme/ race vision or whatever, as you say, theyre ok but still not great. the fog light idea is good, thanks. maybe with LED bulbs in there ? I have found some LEDs that look good, there are plenty available for not too silly money, will maybe try these but looks like might need to doctor the rubber boot, to clear the heatsink/ fan portion on these bulbs. I have cleaned the h/light lens as best I can, but have got a polishing kit to take out the remaining haziness, used just the polish so far but i think need to 'man up' and try the wet and dry. I see AKR have new units available from Depo at reasonable price, so that's an option. the other thing of course with halogens is to ensure the voltage drop is not excessive, previous car I fitted a relay kit, not an issue with LEDs as they operate from 8V. and current is lower. Re the switch it's ok at the moment so probably just needs a good clean with contact cleaner. below was the page I found, M series switch might be similar. thanks again. https://www.hondacivicforum.com/forum/routine-maintenance-diys-73/diy-combination-switch-fix-headlight-switch-74275/

Hi fellas's Its been a while. Sadly I've come to a positio where I have to let her go. It's been one hell of a journey but this car has been sitting under a tarp for long enough now. I think I've done a fair amount of mods and I've learned SO MUCH over the past 5 years of owning this car. Sadly I've grown up a little, got a stock '99 accord that I use for work... Hinata ended up outside for a while, now she sits in our new workshop under a cover. Been sitting for a year almost and barely driven. It hurts to look at her so i've been trying to sell it for sometime now. This sunday someones coming over to maybe take her and drive her again. It's a shame but i've been neglecting this car / focusing on other things for quite sometime and I just can look at her anymore. It's been wild, thanks :)

More work recently completed: Over the Xmas period I decided to do a total suspension refresh on the MB4. I had wanted to do it when i built the car but time and finances were not available. I stripped all suspension off of the car, this took 3 days due to a few issues I encountered. Front end: Firstly, the passenger side front lower balljoint was original to the car, and 130k miles and 25 years had not been kind to it. I ended up having to cut it, and source another set of front lower arms due to how damaged the balljoint taper was. Polybushing all of the front components was a doddle. Whilst the steering rack was out, i discovered the inner tie rods were different to that of every other 90's honda, so unfortunately these were not replaced (I will be converting to a DC2 rack in the future). Reassembly was smooth sailing, until one of the weldnuts sheared off inside the subframe. This meant everything had to come out again (Joy!🥴) I had kept the subframe from my old MB2 (RIP P970NET , gone but never forgotten), so a quick spruce up and this went straight onto the car. Up front I now had Hardrace lower balljoints and tie rods, all bushings were now Energy suspension poly units, I fitted OEM replacement honda wheel bearings from Tegiwa, some skunk 2 upper control arms, and I serviced my Racing logic coilovers. Rear end: This was far more of a pain than I initially anticipated, disassembly was plain sailing, except for the inner LCA bolts snapping (The usual suspects!). Once these were extracted, everything was cleaned and thread-chased. The rear trailing arms were easy to replace the bushes, I opted for uprated hardrace OE style ones for a little bit more compliance. I fitted Skunk2 upper camber arms and some generic chinese toe arms. These were a nighmare to fit due to the locknuts being jammed in the toe adjustment slot, this unfortunately required some "creative" adjustment of the toe arm pocked to allow clearance. The rear LCAs proved the hardest part, due to my Eg/DC2 kit having too small bushes to fit in the outer ends, this required some overnight parts from Scotland to get the right bushes. The next challenge was the shock mount bushes, whuch were the correct fit, however far too wide to fit into my coilovers, these, again, requiring some creative adjustment with a lathe to get to the right size. Whilst the rear was apart I took the time to address a siezed slide pin on one caliper and a few minor exhaust fitment issues. End result: The car now feels brand new, and feels incredibly agile and fun to drive. Body roll and "wandering" around the road has been massively improved. The ride is a tad harsher but this doe not bother me. This was definitely worth the hassle, and didn't break the bank either, costing around £600 in parts in the end I would highly recommend doing this to your MBs if you enjoy spirited driving or B road hacking, its made my MB feel like a racecar! What's next? Next on the list for the car is an update/improvement on the current ICE setup, and some minor bodywork items, with long-term goals being the aformentioned DC2 rack and a replacement engine Unfortunately no photos from the build, however next time I get it up on a ramp I will take some!

VID_20250121_152405_909.mp4

Update: The car is now getting fully wrapped by me since the paint isn't that good and of course some rust spots etc are getting removed....

VID20241227172242.mp4