Leaderboard

To be honest, I've rarely even heard about these switches acting up, so my best guess would be either to just go to a wrecker or buying a used one from someone parting their M-chassis out. There are still enough of those around for that to be an option. And this is just speculation on my part, but I also noticed that pretty much all 90s Hondas share visually the same stalks, be it an EG or an NSX. So maybe that's another thing to look into. Regarding the brightness issue - I myself fitted some ultra bright H4s from Philips that are actually meant for motorcycles, and they are considerably brighter than the normal ones before. But that's still only an alright level of brightness, not neccessarily great. So I always also use my fog lights when driving at night, which really helps light up the periphery. And retrofitting HIDs and LED bulbs is... kinda sketchy and also possibly illegal, depending on where you live. But there are pretty nice LED ones on the market. So you only really got a choice between adding extra lights, getting the brightest H4s, or going down the sketchy route of retrofitting more modern tech into your M. Those 'Ultra Bright LED Laser Matrix Plus whatever' lights modern cars use are just so extremely overpoweringly bright that no matter what you get- as long as it doesn't outshine the literal f-ing sun, you're gonna get the short end of the stick. It's ridiculous.

More work recently completed: Over the Xmas period I decided to do a total suspension refresh on the MB4. I had wanted to do it when i built the car but time and finances were not available. I stripped all suspension off of the car, this took 3 days due to a few issues I encountered. Front end: Firstly, the passenger side front lower balljoint was original to the car, and 130k miles and 25 years had not been kind to it. I ended up having to cut it, and source another set of front lower arms due to how damaged the balljoint taper was. Polybushing all of the front components was a doddle. Whilst the steering rack was out, i discovered the inner tie rods were different to that of every other 90's honda, so unfortunately these were not replaced (I will be converting to a DC2 rack in the future). Reassembly was smooth sailing, until one of the weldnuts sheared off inside the subframe. This meant everything had to come out again (Joy!🥴) I had kept the subframe from my old MB2 (RIP P970NET , gone but never forgotten), so a quick spruce up and this went straight onto the car. Up front I now had Hardrace lower balljoints and tie rods, all bushings were now Energy suspension poly units, I fitted OEM replacement honda wheel bearings from Tegiwa, some skunk 2 upper control arms, and I serviced my Racing logic coilovers. Rear end: This was far more of a pain than I initially anticipated, disassembly was plain sailing, except for the inner LCA bolts snapping (The usual suspects!). Once these were extracted, everything was cleaned and thread-chased. The rear trailing arms were easy to replace the bushes, I opted for uprated hardrace OE style ones for a little bit more compliance. I fitted Skunk2 upper camber arms and some generic chinese toe arms. These were a nighmare to fit due to the locknuts being jammed in the toe adjustment slot, this unfortunately required some "creative" adjustment of the toe arm pocked to allow clearance. The rear LCAs proved the hardest part, due to my Eg/DC2 kit having too small bushes to fit in the outer ends, this required some overnight parts from Scotland to get the right bushes. The next challenge was the shock mount bushes, whuch were the correct fit, however far too wide to fit into my coilovers, these, again, requiring some creative adjustment with a lathe to get to the right size. Whilst the rear was apart I took the time to address a siezed slide pin on one caliper and a few minor exhaust fitment issues. End result: The car now feels brand new, and feels incredibly agile and fun to drive. Body roll and "wandering" around the road has been massively improved. The ride is a tad harsher but this doe not bother me. This was definitely worth the hassle, and didn't break the bank either, costing around £600 in parts in the end I would highly recommend doing this to your MBs if you enjoy spirited driving or B road hacking, its made my MB feel like a racecar! What's next? Next on the list for the car is an update/improvement on the current ICE setup, and some minor bodywork items, with long-term goals being the aformentioned DC2 rack and a replacement engine Unfortunately no photos from the build, however next time I get it up on a ramp I will take some!