Jump to content

hubert

Member
 View Profile  See their activity

  • Posts

    374

  • Joined

  • Last visited

 Content Type 

Everything posted by hubert

  1. hubert
    As with me and Hondas there is always a story. Short version is,after selling my EG the MB6 need to go into the shop for Upgrades so I need another car,that had to be a Honda.had to be a civic,had to be an Aerodeck. Was looking at a few Aerodeck but wanted one that was low cost to run.After reading loads of figures and adds I came across a WHITE Aerodeck just like I found the MB6,buy luck or it was meant to be. this was the one although i would have like a 1.8 the 1.5 Eco Vtech was what I needed,cheap in every thing. I got the Deck in August 2012 so i had it for over a year without touching it and in February 2014 all this happened. After Seeing this,I wanted to take it to the next level as usual I had a vision but I want to not mess the the engine. first i need a Vti-s body kit which was hard to find thanks to Louise Demarco for the for the rear lip and bumper for the Aerodeck and the front for the MB6. then I got the rest if the kit from Adam R Arfiqiue on boxing day i was in my loft spraying then it was time to put the car together after spraying them in the loft on boxing day I could put them on as it was p**sing down with rain so i drove to Bluewater . The rust was a bit of a problem lol I had to remove some mud then i put the freshly painted VTI-S Kit on. the next day i had to rotate the wheels as I had 195x45x15 on the rear and 195x60x15 on the front which made the front look high lol. Comparing THE WHEELS next I went down the road about 2 minutes drive from my house to a crap yard were I found a set of 5 steel for £40 used this site to find the fitments http://www.wheelfitment.net/vauxhall then sent the off for banding next day I did the light and grill the wheels came back in a few days next was the hight, needed low. I have big plans for the Deck suspension but for right now just needed it low using some shock I have in the house as you do,so I set it up I need a jack and a hand so I went to Adam Rafique ,thanks dude for letting me use your stuff. next was choosing the rubber then the test fit now to put it all together on the 31/01/2013 the rubber was ready went to http://www.elitedirect.com/tyres to get the rubber fitted and yes they do stretch with on additional cost did some more work on the rims and tyres and it started p**sing down so i went to Bluewater again
  2. hubert
    yeah,and under the car is so clean I can't bring myself to dirty it.
  3. hubert
    need to start driving the MB6 more but it just keep raining
  4. hubert
    thanks dude,i do it for the love.
  5. hubert
    will do as soon as I build the Aerodeck's thread
  6. hubert
    Thanks dude,I'm hoping when i put the rubber on it will be.
  7. hubert
    the fronts are 8j and the rear is 9j off a Vauxhall Vectra 4 stud Year 90-02 PCD 4x100 Offset 35-45 Bore 56.6 15" thanks to Alex and Ollie wagon Brothers for all the help,if lot knew the amount of photos lol
  8. hubert
    we did lol,but it started raining today.
  9. hubert
    Preview
  10. hubert
    I did,but today i had to raise it for now as i couldn't get into the kiddies school,flipping speed humps lol.
  11. hubert
    looking forward to see you and every one soon.
  12. hubert
    Indeed,just need some toyo px4's hope fully Saturday if all goes well on friday.
  13. hubert
    Ok, really need to stop playing with the Aerodeck. the build will be up soon. what's next 1.More Power or 2.Work on Stance or 3.Suspension or 4.Bay work what do you think?
  14. hubert
    Ollie !!,photos please lol.
  15. hubert
    yes,blue is the colour scheme.
  16. hubert
    I like this build because Dave has taken if to another level,the 1st to K swap a M. not only a swap but a rebuild of the engine and the car. "EPIC BUILD"
  17. hubert
    thanks dude
  18. hubert
    hoping the interior is will not kill me 1.replace the 2 front seats first,these are fibreglass, lighter but not as expensive as carbon fiber. the Sicker Bomb,this will take time a lots of sickers...lol Harness Bar Triple Gauge Dial Pod were the Radio was,this ive done already,it's holding the AEM AFR gauge and a boost guage that will be replaced with a AEM Boost Gauge. Dual Gauge pod dash surround clock holder as i have 5 gauges. i am thinking of removing the rear seat and putting the same as the to front seat to make the car a 4 seater. change steering wheel
  19. hubert
    Had a good conversation with a friend of mines last night,he has helped me and is pushing for me to go all out in 2014,we have diceded to start with the suspension. Rear:new break callipers :powderer coat rear trailing arm :new LCA :Subframe :Breaker Bar :Refurbish Sway bar or Replace with new 24mm :Replace all rear suspension rubbers Front:powderer coat wish born & suspension parts : Replace all front suspension rubbers :4 port big break kit EngineBay :New Reduce pulley :finish bay tuck :relocate battery to back boot :reinstall original washer bottle :smoothed and respray bay :new engine mounts :full length radiator :oil cooler :new oil breather kit :3 point strut brace
  20. hubert
    At the moment I'm trying not to spend on the MB9 Aerodeck but already it's received to much and more is coming lol
  21. hubert
    well,i can say an "EPIC BUILD" but that can mean different things to different people. for example the new wheels will be custom made in the USA,but may need to change the stud patten,so might have to change from 4x114.3 to 4x100 or even 5 stud. The there is the breaks,4 port wilwood or spoon. Changing every suspension rubber under the car,powder coating a few suspension part,new LCA,Subframe,Tie Bar,stabilizer arm,Sway bar link,Sway bar. and that is only under the car.
  22. hubert
    I'm not even sure if I'm half way yet,there is so much to do and not enough money,but this year scarifies will be make.
  23. hubert
    Dude you are 1st on the list for a ride.
  24. hubert
    can we get some up to date photos of the Aerodeck with the Vti-s kit,love that colour.
  25. hubert
    were do you get these done and price please.
×
×
  • Create New...