spudley1988

http://www.ebay.co.uk/itm/M2-HONDA-CIVIC-EK-VTI-INTEGRA-DC2-UK-ADJUSTABLE-LENGTH-DECAT-DE-CAT-PIPE-Z0038-/261380711956?pt=LH_DefaultDomain_3&hash=item3cdb812614 Maybe a daft question but do all allow the flange to rotate? Like would this one be okay and rotate so I can alter position of flange, its also 2.25". Or this one is 2" http://www.ebay.co.uk/itm/Honda-2-4-Way-Adjustable-Test-Pipe-Integra-Civic-CRX-Del-Sol-DA-DC-EF-EG-EK-/191590521333?pt=LH_DefaultDomain_3&hash=item2c9baf59f5 Apologies for probably obvious questions just want to nail right one first time lol.

I've whacked them to a quarter turn from full stiffness and around half turn on the rear ones. Seemed okay from a small drive I had last night

Def not man I think I've lost a few teeth over the years of owning this one lol. Almost rattles interior plastics to death.

Would the 2" mate fine to the aftermarket manifold then yea? I know it's fine with my mongoose end just want to be sure before ordering one up.

I'll go a tad stiffer and if not I'll have to fear the worse I guess. Personally don't feel it's handling anywhere near where it should be

Not sure on age at a guess with my ownership, previous chap and guy who built would be looking at 5-10 years id say. They don't seem to bad rust wise but the ride now to me seems awful and a 1.2 corsa C kept up with me on a run of about 8 miles in which my mb was very poor on corners. I don't expect bmw ride comfort either but these are pretty rough lol, almost fully pollybushed also though I that makes much difference?

Also will their be a certain size i'd require or should all mate together okay?

Guy at work was going to start chopping and welding but if this other pipe will be easier then maybe worthwhile looking at this. Never used one of these before so guessing the flange can be rotated?

Hey folks does anybody have Koni coilovers on their m? Got them on my mb6 just the dampening adjustable ones and to me they seem very bouncy or trashy. Was out in a mates ep3 last night on the same road I'd just came from and his car doesn't react half as bad on the bumps and he just has springs. Is it worthwhile pushing them to even stiffer or is it sounding like they have had their day?

The angle on the bottom of the manifold looks like it has a bigger angle than the bit at the decat pipe, unsure if angle will change much once it' on at the top.

Hey folks just got a manifold yeesterday a used one. The 2 bolt flange at the bottom that goes into decat pipe, should this be straight or is it normal for it to be at a slight angle. I can't remember it ever being at an angle?

Sadly I'm bang in the middle at the minute

Was told by some chap they got banned from here very quickly

Has anyone used this and or had any issues?

Did it cost you much Tom?

Already reasonably low. Rolling arches a big job?

Apologies if it's an overly asked question but a chap is selling a set of xxr alloys which look similar to mini lites. Their 16 inch 8j and possibly et25. How would these be for whacking into mb6?

Thanks for the replies chaps. Ordered a cheap one second hand but didn't realise could get decent eBay ones so will keep an eye on them if this ones poor

Hey folks hunting a manifold for my mb6 but not looking for eBay one as heard lots of issues with these. I was offered a skunk 2 mega power one for 250 but has bottom dented. Is this worth it or is there any other ones worth looking at?

My mb6 system went onto an mb2 so dont see why one woudlnt fit onto an mb3.

Is their any difference to the shine or do they both have a good glossy finish?

Apologies if this is a dumb question but what is the difference between bronze alloy wheels an anodized bronze alloys?

Not fancy going for a custom made system? If not iirc most of the Honda b pipes are the same its the rear box which differs. So b pipe wont be an issue. Would just need to modify a rear box to fit. Message member called 1000rpm and see if he has anything lying around for you. Others may have other members they can suggest you to message also.

Thanks Tom will be taking that as you approve lol. Yea in all honesty I think I'm pretty set on those, think they will look delicious.

Jr3 in bronze look lovely imo.