Krzys Posted February 15, 2018 Share Posted February 15, 2018 3 hours ago, Chandler said: ye its a long way to go to hear a load of people moan and not understand what they're saying I only have to travel south an hour or so 1 Quote Link to comment Share on other sites More sharing options...
dogg1210 Posted February 16, 2018 Share Posted February 16, 2018 On 15/02/2018 at 5:20 AM, Chandler said: ye its a long way to go to hear a load of people moan and not understand what they're saying Same as England then innit bruv fam geezer blood .... . You get me Quote Link to comment Share on other sites More sharing options...
Krzys Posted February 16, 2018 Share Posted February 16, 2018 2 hours ago, dogg1210 said: Same as England then innit bruv fam geezer blood .... . You get me Ah you must have been visiting the back end of butt f**k nowhere Quote Link to comment Share on other sites More sharing options...
dogg1210 Posted February 16, 2018 Share Posted February 16, 2018 Just brought a work boat down from scotland to the Thames. f**k me what a s**t hole lol Quote Link to comment Share on other sites More sharing options...
Chandler Posted February 17, 2018 Share Posted February 17, 2018 On 16/02/2018 at 6:32 AM, dogg1210 said: Same as England then innit bruv fam geezer blood .... . You get me you must have gone to a rough as f**k part to hear something along those lines mate Quote Link to comment Share on other sites More sharing options...
DeLaSoul Posted February 18, 2018 Author Share Posted February 18, 2018 (edited) Some small jobs on the weekend, trying to complete the ECU wiring and tackled the snapped roof bar stud Went back and started from the middle, and twisted the bundle of wires in layers. The ends nearest the plug all had a small curl put in the wires for strain relief once the heatshrink went on Had to extend a few wires for the Lambda so a good excuse to try these new heat shrink solder joints I found online, worked pretty well and look good Pinned the AEM puck wires in a separate shielded cable as per the other side of the loom Want to run the loom up the bulkhead, across and out to the roll cage where the ECU will sit so did a test run first to make sure it fitted. I've since heated and shaped the loom to fit nice and tight to the top of the fire wall to clear the extinguisher pipe Okay, the dreaded snapped roof stud. Had to protect the paint first with several layers of tape just in case before I drilled the stud out and through into the cabin Careful pilot hole..... and it comes through clear of the cage and in a easy place to work from the inside, phew! Time to drill it to size and paint the area to protect it EZ-out on the stud in the t-nut Back on with the end of the roof rail Just the nut to paint and seal later on Will continue the wiring in the week. Edited February 18, 2018 by DeLaSoul 3 Quote Link to comment Share on other sites More sharing options...
Chandler Posted February 19, 2018 Share Posted February 19, 2018 looking good mate! saw those solder joints online before and thought about giving them a try, but didn't get round to ordering any in the end Quote Link to comment Share on other sites More sharing options...
Blackwolf Posted February 19, 2018 Share Posted February 19, 2018 looking good buddy what you doing about the sunroof ? Quote Link to comment Share on other sites More sharing options...
DeLaSoul Posted February 19, 2018 Author Share Posted February 19, 2018 7 hours ago, Blackwolf said: looking good buddy what you doing about the sunroof ? Carbon fibre panel, just needs to be bonded in 7 hours ago, Chandler said: looking good mate! saw those solder joints online before and thought about giving them a try, but didn't get round to ordering any in the end I've been meaning to try them too, had them sitting there for a while and finally gave in. The larger ones aren't so good though, well the ones I got anyway. Quote Link to comment Share on other sites More sharing options...
Krzys Posted February 19, 2018 Share Posted February 19, 2018 Nice! I need to give my roof rails some TLC as they had a bike rake on for a long time and you can clearly see where it had been. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.