Leaderboard

hello, really sorry to jump on the thread, im the girlfriend/mechanic/garage owner, craig will agree with me when i say one of me is enough. so sorry, can't clone me

Couple more of the lights in the pitch black!

Considered and dismissed, they just look so gay.

I think you need to kill whatever piece of equipment you use for videos as it is taking the P out of you mate LOL Looking forward to your pics when you get your spoon replica back on..

Thank you sir mr. Brown!! Wednesday is the hopeful fitting day!!

Lol 😂Here's how I find it easier to do Put window down 1) Pull seal out 2) Remove doorcard 3) Remove plastic waterproofing wrapper 4) Remove the quarter glass frame/bar Has a screw under the door seal at the top and one on the door skeleton 5) Lower window until you can see the two 10mm bolts holding glass on to rail, whilst holding the glass remove the 10mm bolts. 6) Pull the glass out 7) Now the quarter glass can be pulled out to. fit in reverse, DON'T over tighten the two 10mm bolts, just firm. spray wd40 or gt85 down the tracks and slide the rubber in last it will go. Been a while since I have done one, I think thats everything Hope that helps

Still no pictures though?

Hi all time to start my build thread here for my honda civic ma8 the plan for this it to get it to look like a mb civic which i will show all once i has been done work in progress are some pics to start off this is how i got the civic this car was taken to my garage for welding work on both rear arches and this is the engine bay here are more pics these are from the crash lol more when we finally found out how to remove the wing (bare in mind i never worked on cars back then) This is the doner car that my dad had bought this would have been an mot failure it was in bad nick car had about 133982 miles while mine had 98k when we finally got the bumper of this car and that bumper ^ was put the before we put on the new one so it looked like this pretty much that was how it looked once done removed the front end me and my dad then started building up the bad boy civic During then we noticed small faults with the car like brake cylinder leaking cracked center console etc As u can see it not the same colour as the bumper and wing don't match the car one bit but that was the only way of keeping the car this is how my civic looked inside biit of a mess back then i'd say it toke me and my dad most of my school summer lol as i remember going back to school once it was bulit here a shot of both cars last touches were needed like hub caps boot cover parcel shelf etc car was taken on a test run back then it seem fine just before we had finished my dad noticed a leak from the the rear drums i don't no if u can see well in this pic lol but it was more worse on the day this one is not a really good pic but as u can see the center console was ripped out as mine was cracked and damaged i wanted to have a better one in place and see as the other civic had a better one i replaced them the last touch to finish the car was the rear lights as mine had faded once the car was done i was given in for mot which it failed one need o/s/f wishbone are o/s/f drop link and weirdly my dad had put the rear brake the wee spring on the wrong way ;s but i did not have any pics of it done well i say it's time to move on to the upgrades 1st upgrades were the lights xenon 110 brighter lights that was basically the 1st upgrade till i got in my garage 1st day in the garage lol 1st upgrade i had done japseed induction kit as u can see the rocker cover was a very s**t job done by my dad's pals the 2nd upgrade i had done was black smoked indicator then my 3rd upgrade was white dials plus the carbon look trim then i gave the bad boy a much needed service with better engine oil no picks bar this one lol

Oh Damn I think you are not on that page. .they are in Cornwall also. 15 inch alloys

They look like quality lights! Shame there isn't any aftermarket ones made for our Civic's....

One of my favorites too Cheers Na I think 17" are too big for a small engine like mine. And tyres are not cheap!

That's a shame, bring the noise.

always liked these two, they belong to a couple of mates of mine in Inverness

Roll on wednesday... Hopefully!!!! Aye.

Looking almost new, good job.

No time for sleep its a new day so get out and get some pics lol

You know you can post the updates in a new reply rather than just updating the first post as the replies will make more sense that way lol

Update tried fitting those new fogs to the original metal bracket from standard fogs and it doesn't work so the bracket that comes with the new fogs I have screwed into the holes in bumper like I said before the stick out a tiny bit but I don't care don't really fancy paying 60 for fogs that I can't put my h.i.d's in

Awesome mate. .I will definitely be getting 6k ones I think even though I like 8k more you are right less chance of being pulled with these. . Seems a lot brighter still compared to standard. .can you show a few pics of how you installed them and where did you put the ballasts.

Try plastidip or wrap, at least that way if you don't like it it's easy to put it back.

Herne bay! Stopped by Sir Hatman of Esq on the way back! We enlisted another Sir Esq within minutes of my arrival! I'm just at Peterborough services now having a p1ss stop! Been an epic trip! Will tell all tomorrow when I've had some sleep!

I´ve sorted the reversing lights problem after some time spent near the engine bay but finaly it´s ok The problem was this connector it had cracked one of the connections inside, so I had to cut the cable at both ends and make a direct connection to pass out of the connector This is the connector and the result: Connector:

Thanks Matt, getting there! Got the tyres getting fitted tomorrow then going to spray up the wheels on sunday. Matt silver very soon, cant beat a matt bora

Stickers are on! Also the car is still dirty because well, it got dark pretty soon after I went out so I just dumped the a bucket of water over it and used wet wipes over where I wanted to paste stickers. At least I wiped 90% of the bird poop off! Damn seagulls. Full height coverage! There's room for a couple of smaller stickers in the gaps, just need to find ones small enough! I ordered this in silver, but it came white. Ah well. The S on the driver's side went a bit screwy but you don't notice it from a distance. Oh and it appears I have 200 posts now. Where's that membership button?

It made for good viewing! Shame only 50% was captured!

cheers boys, its looking better, made a make shift temp bench out of the old wardrobe Also met a bloke from the audi service centre across from us, i had to weld a gear stick plate for him, hes got a modded 400 torque bora and he loved the accord thought was really retro which was nice. i finally have somewhere to jack the accord up and i can leave for days on end lol

Loves a video