Jump to content

vtec2011

Civic5 Supporter
 View Profile  See their activity

  • Posts

    3,562

  • Joined

  • Last visited

  • Days Won

    6

 Content Type 

Everything posted by vtec2011

  1. vtec2011
    I can do that. Pictures will be on my progress / project thread or MIGHT post a how to...
  2. vtec2011
    Thanks man! I love how she sounds... I have been tempted to fit the Piper backbox but I'm happy with it
  3. vtec2011
    I am in the same situation mate. I'm looking for a set of HT leads for mine and seen a couple cheap 8mm leads for d-series. But I don't know if there all the same!
  4. vtec2011
    Thanks lads! I cannot see any leaks, I even had it up on the ramps to check. I checked the slave cylinder, looks fine. Gear linkage seem to have a lot of play so I re adjusted it and tightened it up. No difference so far... I will bleed the clutch soon and might just go for a new clutch anyway. It wasn't looking great when I seen it last year. Thanks again
  5. vtec2011
    New sidelight led's and rear number plate led's. They're super bright and these are no cheap ebay sh!t I have also uploaded a video of what she sounds like with the new induction kit
  6. vtec2011
    Haha yeah sure! if you need any help, just ask... I got the induction kit for my birthday last month and yes it's from ebay. I'm posting a video soon to show what noise this induction kit gives
  7. vtec2011
    That's better! Smoooooth......
  8. vtec2011
    Wow! Awesome! I bet they keep you busy and good luck on the wire tuck. I'm scared too as I'm wire tucking the whole engine bay on my M soon
  9. vtec2011
    Looks stunning Mr B! Have you got anymore plans for her like... giving the engine a bit of colour?
  10. vtec2011
    I am clueless when it comes to carbs... Stick a K&N carb air filter on
  11. vtec2011
    That is why I asked if your de-cat got a recess for the o2 sensor. I think it looks like you will need to get another one And I think you should have gaskets with your de-cat?
  12. vtec2011
    Shame it's blowing and I agree with you there, I hate the sound of blowing exhaust. I know this sound stupid but you did make sure the bolt for the lamba sensor recess is done up tight, right? My mate done that mistake and a screw on type bolt eventually came off. Instant loss of power and sound worst than a Fleabay fart can
  13. vtec2011
    That is awesome Nick! Wish I got one of those instead!
  14. vtec2011
    To those who don't know, last year or late 2011 I have put another gearbox in my MB3 which is from a 2000 1.6 Civic Coupe. The code casted on the gearbox is B000 P9A. Just recently I had trouble getting it into 2nd and 3rd gear. It only does this when I'm gearing down. It does it when driving it easy or hard. I can be driving in 4th and when I want to slow down and go into 3rd, it's nearly impossible! It doesn't crunch or grind, it just simply won't go into gear! It's got Honda MTF oil in and I have checked the levels. One thing I didn't do is change the clutch when I fit the 1.6 gearbox. Could it be a weak clutch or maybe clutch fluid? Thanks for reading and thanks in advance
  15. vtec2011
    I really like it! Just need blending in a bit And LPG? You got a very different Aerodeck ere haha
  16. vtec2011
    Nice! What was it like to apply the flyeye tint? And the exhaust looks cool. I got a exhaust tip on mine too
  17. vtec2011
    Looks awesomely mean... I didn't know you carbon wrapped the center part of the lip. I must see this car in front of me to see what else I haven't spotted yet!
  18. vtec2011
    Ripspeed?! *Facepalm* I have never taken the centre console out before but that looks like a b!tch to do... Keep up the good work!
  19. vtec2011
    Looks good! I can't wait to see the finished results. Is your boy going to respray the underbody / skirts too?
  20. vtec2011
    Thanks for your reply and info Emil! I have been searching all over the internet to see if I achieve anything from doing this swap. It just looks better and sounds better apparently... There should be a reason why Honda didn't put these inlet manifold on our D15Z8 in the first place but... oh well, I am just going to go ahead to do it haha. I will look into how to modify the throttle cable and bypassing the coolant hoses. Thanks again
  21. vtec2011
    Haha Honda's always get you from A to B
  22. vtec2011
    I just looked at the above picture and realized I forgot to connect the lamba sensor Thanks mate! It is quite easy to do but it's waiting for paint to dry the boring bit. And if your using your car all the time, it can be a pain LOL BUT it's totally worth doing! You feel proud opening your bonnet seeing shiny clean stuff
  23. vtec2011
    Yes that will go straight on mate. I recently got another rocker cover which is from a 1.4 Civic for my MB3. It fit straight on. All d-series rocker covers are direct fit apart from the old ones with the spark plug recess at the back. Looks very clean! If you need any help, just give me a shout
  24. vtec2011
    x2 to what Emil said Sorry I have to hijack this thread but... I got a d16z6 inlet manifold for my MB3 ( D15Z8 ) and it's got throttle body, injectors, fuel rail and blocked egr valve. Its all from a D16Z6 engine. Is it worth fitting all this to my MB3? Will it go straight on mine? Thanks in advance
  25. vtec2011
    Nice! I don't have the patience to carbon wrap fiddly stuff like that... Now strip the roof liner and carbon wrap that
×
×
  • Create New...