Leaderboard

Hi Ben, The calipers in the photo are for the 260mm front brakes, not the larger 280mm front brakes. Manufacturer caliper numbers for the larger calipers are LCA333 & RCA333. You can use eBay to get the oem numbers from them. Basically the calipers are the same for the mg zs180, mg zr160 & accord of that era, but the carriers differ i believe (ive not checked any fit on an mb other than a zs). I can confirm that the calipers and carriers from the zs180 will fit onto a mb2 4x100 as thats what I'm currently running! If youre upgrading the brakes you'll need to change the master cylinder and prop valve if you don't have abs for it to work properly. My setup is: Honda Civic MB6 brake master cylinder Honda Civic MB6 brake servo Honda 40/40 brake prop valve (46210-S5A-912) Wezmoto Braided front and rear brake lines (700mm front / 560mm rear) MG ZS 180 Front & Rear brake calipers MG ZS 180 Front & Rear brake discs Cheers, Dan

Finally getting around to a build thread for my third car It all started on a dull early may day. A Friend of mine messaged me, asking if I needed any parts from her MB4 before she scrapped it. It had been sitting on her drive since she her daughter had been born. I said to her, "let me know what the scrappy offers, and i'll chuck £50 on top and come grab it", knowing that the d16w4 powerplant in this could replace my lathargic D14 in my MB2 The next day me and a mate collected it, threw some trade plates on and ran up to my workshop. Even with the old 4 speed slush-box, and a years neglect, the MB4 walked away from my MB2 on a straight bit of road. Once we arrived, my friend parked the car up and then headed home. I then stood and had a smoke, looking at this car having a "Wangan midnight" esque moment, seeing the colour of the Sicilian Red paint for the first time. Plans had changed. (see attached image) Rust and engine work: First I got the car up on stands and made a list of everything wrong with it. The rear passenger sill and inner arch passed the good old screwdriver test, however the driver's side failed miserably, along with a few places around the front jacking point, and front inner arch. Out came the grinder, welder, and some conveniently shaped and cut sheet metal that I would be using to patch these big holes. This was a steep learning curve, as I have only ever done agricultural welding, and never thin bodywork. Once the rust was dealt with next came the auto box - I had never planned to keep this gearbox, so the hunt for an s20 close ratio box began. During this time, the auto box, torque converter and PRND lever were all disposed of in an appropriate fashion (Thrown into a skip as fast as humanly possible🤣), meanwhile, the engine was suspended by a ratchet strap around 2 on the gearbox bolts, and a random 2x4 i had laying about across the wings (See attached) Whilst the box was off, I decided to replace the rear main seal, sump gasket, and clean out the oil pickup tube. A few shiny parts were fitted during this time too, including an oil sandwich plate with senders for both oil pressure and temp, HKS oil filter, TTV flywheel and an exedy stage 1 clutch. Once I sourced a box, the new mounts were fitted up and after a copious amount of faffing around the engine and box were in. (I wish I had an engine crane!!) I altered the wiring on the PRND plug to disable the inhibitor switch, as well as the reverse lights. I finished under the bay by rebuilding the distributor, replacing the plugs and HT leads. I also added a bus bar to the firewall as my battery was going to be boot mounted. I am using a Janspeed 4-2-1 manifold, a smashed out OEM cat shell and a Skunk2 megapower exhaust system. I have a Whale pen15 air intake as well. Interior: This car had a creme interior, which I knew wouldn't survive me daily driving it. I quickly tore this out, installed a load of sound deadening and the various wires i'd be needing for my ICE setup, then fitted a black carpet and VTI "bus seat" interior. I mounted the battery and circuit breaker in the spare wheel well, as well as a power distribution block. this would be needed when I got around to building the boot and fitting my 3 amps. I finished the interior off with an oil pressure and temperature gauge set, a fire extinguisher, and an old school pioneer flipout headunit + DVD player. Exterior: The exterior is largely untouched, as it is the rare sicilian red pearl colour. This car was factory specced with a full VTIs kit and Jordan wheels. The jordan wheels went onto my other MB2, so that I could fit my 15" TSW imola wheels. I welded the rear wiper hole up, and the old spoiler holes. I then fitted an "auto spoiler", which had been preiovsly fitted to a friend's recently imported 200sx. This was an almost perfect colour match.

See attached, will be posting some more in the near future about rebuilding my engine haha

Hi folks. Had a 2010 Civic TypeS GT in red (aka Sexy Lexy) about 9 years ago, followed by a 2008 Civic TypeR in silver (aka Roxy). Traded the TypeR in for something more sensible for a daily driver, and have had a load of various cars since then. Always missed my TypeS tho! Was supposed to be looking for a classic 1980s Vw Golf convertible or an old Scirocco, but got fed up looking at sheds. Decided plan B was needed which was to sell my 1st Gen MINI Cooper s convertible and get a sensible daily driver again! Initially looked at 10th gen civics, but wasn't too keen on the style, so the hunt was on for a TypeS GT again (pref in red). Had to be the GT, had to be the 1.8 and no older than a 2010. Found one down in Yorkshire for £4.5k, years mot, service history, 64k on the clock,in red....and even the first 2 letters of the reg were the same as my old one (OE). She drives like a brand new car, so happy to be back in an 8th gen! Only got a few pics of her so far but will get more. Hope you like! Some subtle mods on the way, pretty much the same as I did withLexy senior lol Oh, and also means DD is relieved of the daily driving duties, so tucked up in the garage. Means I can spend time getting her back to show standard now!

Hi all, So I can confirm aftermarket seats, without cutting frames or welding mounts to car, are completely possible. If you have read my before method with the universal frames this way is a lot easier and more cost effective. After 3 months of research I found a company called Planted Technology, they produced made to order seat sub frames for many cars. I emailed them to ensure my car was not an EK or an EG. I measured up the cars holes and got back the details of the closest fit frames they make. The Honda Accord 4th & 5th gen have the same interior as the MB3/MB6. I took a risk bought the frames and they do in fact directly fit. I admit it was a bit of a fiddle as they had to come from America so may have been slightly warped or bent on delivery, never the less I got them in as seen in the image below Here is a link to the main page, it would better off ordering them from GSM performance Planted Technology https://www.plantedtechnology.com/products/planted-seat-bracket-honda-accord-4th-5th-generation-1989-1997-passenger-right GSM performance https://www.sportseats4u.co.uk/product/planted-honda-accord-bracket/ Things to consider, these frames do not come with threads. M12 Nuts will be needed to fit seatbelts, M8 Nuts and bolts to fit seats to rails or frames, washers highly recommended

Smaller power steering pulley (hopefully it will clear the bonnet without hacking any big holes in it) and 10% underdrive alternator pulley fitted As we've deleted the AC the factory belt was much too long (think it was something like 7pk1735 from memory). Managed to find a belt that will fit (7PK1400) - it seems ok but apparently there is a mark on the tensioner that you can check - i'll do this next time im with the car to confirm but seems like the right size. Engine mounts ordered - I went for Innovative Mounts for a Civic EG as the price for Hasport mounts in the UK is insane (£700+!) and I wanted to avoid ebay china copied junk on this project...

Thanks for the update on the fogs - I managed to get a set of good condition blanking plates so i've removed the fairly rotten big fogs for now but I may reinstate them later. Left the connectors tied up behind. A bit more progress on the K-swap side of things: Drilled a couple of holes in the firewall just under the heater outlet to allow for the shifter cables to pass through (no photo, oops) Got hold of a billet shifter plate designed for an EG but it was sitting too proud of the tunnel so drilled out the fasteners for the shifter base plate and removed it DC5 shifter mocked up - was worried that it would be too close to the dashboard but it seems to just about be ok - the shifter box came with a short shifter already fitted which should help things Clutch and flywheel test fit - just waiting for various missing bolts to arrive from Japan before buttoning it all up. Toyed with the idea of getting an uprated clutch but we've gone with Exedy OEM EP3 clutch for now as it's many times cheaper than an uprated one (£126 vs ~£400) and I reckon it'll be OK for NA power levels. Any future plans to boost the car would require an LSD as well as a clutch upgrade anyway! Flywheel is a Competition Clutch 3.9kg

Happy Christmas everyone! Hope that you're all having a great festive break! 🎄🎄🎄🎄

You are technically right about not needing the whole trailing arms, but good luck with both finding the spindles by themselves in usable condition and taking the old ones off. Finding parts like that is getting progressively hard as our cars start to turn into oldtimers, and most of these super specific upgrade parts have already been grabbed about a decade ago. We're kinda late to the party in that regard. The spindles are also secured to the trailing arms with extremely strong threadlocker, which oftentimes are pretty old and corroded on top, which makes removing them near impossible without drilling them out. Stripped a bolt attempting to remove the disc brake ones, even with applying heat and using rust remover beforehand. No chance. So, yes - you technically don't need them, but realistically you will. Except if you're fine with drilling all of the bolts out and dealing with that headache. And the part about bleeding the brakes is also generally correct. Most cars have their brake systems set up like that so you can still come to a stop if a brake line fails. Otherwise if you combine FR with RR / FL with RL you will only have working brakes on one side of your car, which I don't have to explain why that would be very bad.

Hey all, already done a load of restoration as getting it back to full N/A Glory before I consider ITBs. Just wanted to make a meal of this that arrived the other day, so happy! 🥰

ok, its been some time... but i want to share few photos from a civic photoshoot i made recently. This is how it currently looks like.

Amazing reply from SirPaperbag! Just to add ive done this swap on my (non abs) mb2, but also upgraded a few things. My setup is as follows and works sweet: Disc trailing arms off a mc1 aerodeck MB6 brake booster MB6 1" master cylinder Mgzs 180 282mm front calipers (interesting the caliper is the same as from a 97-03 accord, not sure on the carrier) Mgzs 180 262mm rear calipers 46210-S5A-912 40-40 prop valve Regarding the rear arb - the rear brace that SirPaperbag mentions won't fit without modification. DeLaSoul mentions it in his build thread - if I remember correctly the mounting points where the LCAs mount to the chassis are about 8mm narrower on our MBs to EKs

Small update on the whole brake prop valve situation: Apparently, EG6 prop valves could also work, as they don't have ABS and 262/242mm rotors in the front and rear, just like our M-chassis Civics. So, if that's true, you could get a brand new valve for less than $200 from Japan. Part number for these bad boys is 46210-SR3-013 And you should be fine sticking with your original brake master cylinder + booster! But if you've got 242mm discs all around instead you'd need a "1725" valve (46210-1725-XXX) off a Del Sol, not off an EE/ED/EF Civic! (Different f/r rotor sizes)

Got some from Climair installed rn, and they fit very well. They're still available brand new. Only thing I had to do is grind off a bit of the holding tab in the front (was a bit too long) but that's completely normal with these things. And you can even choose between clear, tinted, and dark, which I find quite nice.

Good shout mate, I'll se about getting this added to FAQ. And thank you, cracking info there!

A reply this detailed deserves to be in the FAQ section of this site! It really seems a more difficult job than a cam swap and a tune haha If I ever manage to stumble upon the main parts for a cheap enough price (Hondas in general were very expensive relative to other cars here in Italy so not many sales...) to justify all the work I'll definitely try. Thanks for all the info!

Great post there mate

The part about needing new trailing arms is 100% correct, as the drum brake ones lack the proper mounting points for a disc brake system. But you've got to be careful with which arms you choose, as the wrong ones could end up increasing your rear trackwidth and that's gonna end badly for your handling. As our M-chassis have borrowed a lot of suspension components from 5th gen Civics (EG), I'd recommend searching for EG5/EG6/etc. trailing arms, as they should keep everything in spec. I for one got a pair of EG5 arms to go with my non-ABS system. But that's only part of the problem. If you've somehow managed to get yourself the right trailing arms then you still have to find a matching brake proportioning valve (or prop valve) that splits the pressure correctly between front and rear. Otherwise your rear brakes might either not bite enough, or bite too much and cause the rear to kick out while braking (very dangerous). This is especially important if you've got something like an MOT or TÜV here in Germany, where your car gets an inspection every X years and they check your brake performance. M-chassis Civics also use an old style of prop valve, which makes it EVEN HARDER to find the correct ones. What you generally want to get is called a "4040" valve, which is just the model number, nothing more (some dumbasses online claimed those valves split 40/40, but where the hell would the remaining 20% go?) I also found a nifty table somewhere on an obscure forum, and I don't know where exactly I got it from, so I sadly can't attribute the original poster, but here it is: And depending on the caliper sizing, you might even have to upgrade your master cylinder, but that's getting really technical. So, in short, get the correct trailing arms, a somewhat correct prop valve and maybe upgrade your master cylinder. If you want to do it properly, it's a whole lot more work than just doing enough for it to work. Pro Tip: You can also fine-tune your front/rear balance by using more or less aggressive pads. And regarding rear ARBs, you've got a choice between either buying some used EG6 brackets, using aftermarket ones, and reinforcement braces with mounts included. I went with a used EG6 ARB, plus mounting hardware, because I wanted to try out how much difference just that dingy little thing would make (a lot). Here are a few pics of it both installed, and some pics of the used mounting hardware. You also need fitting lower control arms with mounting holes for the endlinks. And I'd recommend buying new endlinks while you're at it. And maybe a few harder rubber bushings on top. I also had to fabricate some small metal standoffs for the mounting bracket to properly fit to the rear frame (top right picture, the screw just above the yellow marking). This would be the alternative, a rear brace with mounts included: But some places also carry aftermarket versions of the OG hardware that I mentioned and shower earlier, so that's an option, as well. All in all, it's a s**t job with tons of little hang-ups, researching, browsing marketplaces and painful installation, but the handling difference is night and day.

Heya bud imho, dual rads are a terrible idea. They are both looking to dissipate heat, but when connected, if you feel the desire to move rapidly or it's a very hot day, the heat in the rad will affect the condensers ability to be effective, thus you would lose cooling ability. I guess it's like putting you home fridge in front of the radiator, if the fridge can;t shift the heat, the gasses can't re condense and the fridge loses it's ability to be effective. I think it would more be a limit to the age of the technology of the aircon, pressures used today are greater and condensers are far more efficient. I say delete the aircon, get a bigger rad and just drive faster with all the windows down! haha! I say when my MB6 VTIs still has it's full aircon :P

Thank you guys. I'll try to make a topic of the work in the car I've made so far and all the work I want to do. @SirPaperbag The fog lights are not factory ones but some cheep chinese. I found the originals , bought them but I think the front bumber is an aftermarket bumber so I have to cut the whole thing in there to fit the original factory fog lights. Lots of work has to be made generally and have no time. Nevermind whenever I find some free time I will do it. The grille is handmade, I tried to fit the H emblem from my previous EK civic, but it's too big :( Only the small H emblem of the pre-facelift fits. By the way the car was imported from Germany, as the user manual of the car is in German :D

On the night shift downtime and was having a read through this thread, thought the car looked awful familiar. Saw it at cadwell a while back, with presumably its new owner. Looked and sounded amazing, went like f**k too! ahaha

Whoops, hope these work haha. Got round to fitting most the parts - also fitted a k-tuned rep short shifter with a stainless weighted knob which makes the car feel so nice to drive - will get a photo soon. Me and my wife have also had a baby so time and money to work on the car are in short supply!! Next steps are to get the interior sorted - really want to fix the headliner, and seeing Kaleverada's thread has me inspired for the pillars! Also really want to strip out the back, tint the windows & fit bucket seats...

So, did a good bit of work to the car again. This time I installed a proper mounting bracket for the cold air intake as the old hacked-off and jury-rigged intake mani bracket looked pretty bad, to be honest. Also installed a pair of much more serious sounding horns than that little beeper that the car came with. They sound a lot better than the OEM one did, and are quite a bit louder on top! After that I installed a set of new bumper screws - the original ones were completely rusted and cruddy, and one almost stripped completely when I took that bumper off! Then I got to work on my seat-project. As I said in my last post - the original seats make me sit a bit too high for my own tastes and I have been looking for either some high-quality (road legal) seat rails for aftermarket seats from either Recaro or some other brand, or a completely different way to sit lower than the original seats would allow me to. As it turns out ... you can fit CRX seats on the original M-chassis rails if you drill out the rivets and fabricate an adaptor plate out of steel (10mm thick in my case). I got lucky a few years ago and managed to take a pair of these seats off a guy for jsut 250 bucks total. :) Here's how the first prototype looks like: This was only to take a look and see if my idea could even work to begin with, and if it would make me sit lower than the OEM seats would, but as luck would have it ... this combo works flawlessly and I sit about 5 to 8 centimetres lower than I do in the stock seats! :D They are also quite a bit more comfortable, if a bit worn-out. Real plushy. :) But as things stand right now I'll just make a few more refinements to my adaptor brackets, give those seats a thorough cleaning session and maybe add some more side bolstering to give them a bit more of a sporty feel and I've got myself a nice pair of OEM Honda seats that do exactly what I want from them! :D

So, a few boxes full of fun-parts arrived yesterday... :D I'm still trying to find a good machining shop to get a port and polish, a valve-job and to get the rotating assembly properly balanced, but things are slowly progressing on the new engine build. It's going to be unconventional for sure, but I'm going to be fully building an N/A D16Z6 that I've bought for this project. Forged conrods, high compression pistons, stage 2 camshaft, lightened flywheel, the whole nine yards. I've also done some test-fitting already and it seems that the 'LITE'-series of conrods from Skunk2 doesn't require any notching of the block to fit, which is a huge win in my book! Though I had to cobble together a pseudo-piston from a few pieces of plastic and foam for the test-fit, as the pistons I bought are .5mm oversize and I haven't had the block bored out yet. Worked super well, though! But I'm super stoked to see what kind of power gain this is going to get me, and especially how high I'll be able to rev it. Components-wise it should be fine up to 9.000 or even 10.000 RPM, but we all know that it probably won't make much or even any power up that high in the rev-range. Based on my research into other all-motor D16 builds and B20 builds I'm confident that it should definitely hold up to 9.000 relatively comfortably, as many people in the states rev their stock-rod B20s that high without much issue, running only ARP rod-bolts and nothing else. (B20 engines have the same stroke as D16s, btw) It's going to be a while until things get moving properly, but the first step has been taken and all that's holding me back right now is finding that machining shop! :D Some folks are probably going to ask why I would take a D16 that far instead of just going B-Series, and I'm going to answer that by telling you that a B-Series swap costs around four to five thousand Euros where I live. If you can even find one... That's a lot of money for just a stock engine and trans. And it's also why I'm going to spend about the same amount of money to build a D-Series that is going to make roughly the same power, as well. I simply want a built engine. Simple as that. I've always wanted to build a proper all-motor engine and I finally got the chance, both time- and money-wise to do so, and I'm going to do it! :D I've also been doing some research into getting a road-legal bucket seat, or any kind of seat to be honest, because the stock seats are just too high for my tastes and I constantly have to lean forward when I'm stopped at a red light. Someone else on this forum already made an extremely helpful post about the seat rails from Planted Technology, which helped me immensely, but I've also found a local engineering company here in Germany which is able to fabricate everything in-house and even get it entered into the car's paperwork the legitimate way. That comes with its price though... Well, anyways. That's the current state of my project. See ya 'round!

Sensor for the ir remote I believe.

After nearly a month delay with far too many emails back and forth we finally got hold of the replacement engine mount bracket from Innovative Mounts and the engine is now finally bolted in! Got a few other bits fitted after this photo like the radiator, hoses, and fan, and then started to work on some of the plumbing like the clutch line. Getting exciting now - to be continued!

thanks Simon 👍 yes looking at the rubber parts, found the parts for the top e.g. Items 9 & 6 , struggling with the bump stop ATM, Item 11, PN 51722-st3-e01.

Quick photo from last night. Looking forward to the suspension refresh and getting this thing slammed. Other news - carpet and some dash trim is out ready for welding.

yeah it should be compatible.

Quick test pic

Progress so far Started to strip out the engine - radiator (probably leaking) and AC condenser (also probably leaking) removed: Painting the rear bumper - to cover various marks and scratches but also somewhat of an experiment to see what it looks like with rubber strips colour coded (from photos i've seen I think it will look better) I've started putting together a list of parts that i'd like to acquire (the amount of small parts you need for a K-swap is crazy. It's all bolt on but you definitely need a spreadsheet or similar to manage it!)

More work recently completed: Over the Xmas period I decided to do a total suspension refresh on the MB4. I had wanted to do it when i built the car but time and finances were not available. I stripped all suspension off of the car, this took 3 days due to a few issues I encountered. Front end: Firstly, the passenger side front lower balljoint was original to the car, and 130k miles and 25 years had not been kind to it. I ended up having to cut it, and source another set of front lower arms due to how damaged the balljoint taper was. Polybushing all of the front components was a doddle. Whilst the steering rack was out, i discovered the inner tie rods were different to that of every other 90's honda, so unfortunately these were not replaced (I will be converting to a DC2 rack in the future). Reassembly was smooth sailing, until one of the weldnuts sheared off inside the subframe. This meant everything had to come out again (Joy!🥴) I had kept the subframe from my old MB2 (RIP P970NET , gone but never forgotten), so a quick spruce up and this went straight onto the car. Up front I now had Hardrace lower balljoints and tie rods, all bushings were now Energy suspension poly units, I fitted OEM replacement honda wheel bearings from Tegiwa, some skunk 2 upper control arms, and I serviced my Racing logic coilovers. Rear end: This was far more of a pain than I initially anticipated, disassembly was plain sailing, except for the inner LCA bolts snapping (The usual suspects!). Once these were extracted, everything was cleaned and thread-chased. The rear trailing arms were easy to replace the bushes, I opted for uprated hardrace OE style ones for a little bit more compliance. I fitted Skunk2 upper camber arms and some generic chinese toe arms. These were a nighmare to fit due to the locknuts being jammed in the toe adjustment slot, this unfortunately required some "creative" adjustment of the toe arm pocked to allow clearance. The rear LCAs proved the hardest part, due to my Eg/DC2 kit having too small bushes to fit in the outer ends, this required some overnight parts from Scotland to get the right bushes. The next challenge was the shock mount bushes, whuch were the correct fit, however far too wide to fit into my coilovers, these, again, requiring some creative adjustment with a lathe to get to the right size. Whilst the rear was apart I took the time to address a siezed slide pin on one caliper and a few minor exhaust fitment issues. End result: The car now feels brand new, and feels incredibly agile and fun to drive. Body roll and "wandering" around the road has been massively improved. The ride is a tad harsher but this doe not bother me. This was definitely worth the hassle, and didn't break the bank either, costing around £600 in parts in the end I would highly recommend doing this to your MBs if you enjoy spirited driving or B road hacking, its made my MB feel like a racecar! What's next? Next on the list for the car is an update/improvement on the current ICE setup, and some minor bodywork items, with long-term goals being the aformentioned DC2 rack and a replacement engine Unfortunately no photos from the build, however next time I get it up on a ramp I will take some!

Need to see the pics of this one 😎

Basically any D-Series manifold will fit all kinds of engines out of that particular family. Except D17s, those are "special" (aka the worst engines Honda ever made). Got a 4-2-1 header myself that I bought when my car still had the stock D14 in it and it directly fit my D16Z9 without any modifications. And I can attest to the rust concerns - my rear arches were pretty bad (but still manageable) when I got mine, the front corners where the fenders meet the sideskirts were rotten through and the rear corners are also slowly starting to bloom, as well. Definitely make sure to check those spots when you've got the time! Oh, and your distributor is probably going to die at some point. All of them do, it's kind of inevitable. Do yourself a favor and don't get one of those repro units when it finally goes out - Blueprint and Yingzhen and whatnot units are all Chinesium garbage. The only high-quality replacement I could find was one of those rather tacky sounding "Dragon Fire" units, but quality-wise they are pretty much OEM+, made in the US (not China), and even provide a stronger spark than the stock dizzys do. Other than that, welcome to the club! :)

Apologies for the Lack of updates, Im still on with the Restoration and will get some updates posted soon!

I have actually used both Rainsport 5 and the AD08RS tires, so I think I'll just throw my two cents in here. The Rainsports are literally a 10/10 in the rain - I once drove on the Autobahn during a heavy rainstorm with around 130kph and I didn't get even the slightest bit of aquaplaning at all! But their dry grip is not the best to be honest. They tend to understeer and 'smeer' during cornering, so maybe a 7.5/10 in that category. The AD08RS are also very good in 'bad' (rainy) conditions - I'd give them an 8/10 in that regard, they grip quite well in the wet for semi-slicks. When I went over to my mates' to put the new tires on my wheels it was still early February and quite the rainy evening, but the brand new tires didn't feel slippery or dodgy in those cold and wet conditions at all! (Around 5-7°C and quite a lot of rain) Their dry grip is in a completely different league as well - the car feels like driving on rails compared to the old Rainsports. On my usual B-roads there were a few corners that always felt a bit dodgy/understeery when I took them with 100kph, but the Advans give me nothing but confidence! So, my recommendation for you would be the AD08RS. Their dry grip is almost perfect in my opinion and they are good enough in the rain, especially if it's mainly a dry-weather car. (And I use them for my daily, so...) Plus a few pictures comparing the fitment (same tire sizes for both of them):

Glad he's enjoying it. Really shouldnt have sold it tbh. Moment of madness haha.

Meant to update this! Headlight was smashed to bits at the back so fitted one of my spare ones. Slam panel was slightly bent but got it bang on straight again so headlight sitting flush with bumper/wing/bonnet again. Managed to cut a small metal plate to size and riveted I to ghe top of the bumper to replicate the bolt holes that were ripped off the bumper, so it's now bolted back into place solid using the original bolt holes on the wing. Still got a nasty crack, but tbh looks pretty decent and least she's back on the road. Picked up the new bumper and crash bar, so will get them painted and fitted along with painting the front spoiler and bonnet. Thanks to Camy also picked up a job lot of spares including two front wings, steering wheel, oem honda civic MB/MC radio, injectors, and various other bits....all for £20! Then got the aerodeck spares car to call about when we get back from hols tomorrow so might have a complete deck for spares. Things looking up in DDs world again! Will post pics of the repair now she's on the road again.

Bay shot because why not. Changed whale d**k out to actual carbon fibre one, and changed rocker cover to a fake Mugen one. Looking a lot tidier under there now!

That blue looks stunning! Loving the car in its latest form mate!

So over the winter months i have been refurbishing numerous parts off the car. Stuff like the Fuel Tank, Straps, Filler neck etc. This is the filler neck off my car, its pretty rusty, however thankfully no holes, I cleaned it up best i could and treated any rust, then etch primed it. once that were done, i then painted it satin black. Next up was the Rear Lower Control arms, These are a Spare set so thankfully i can do them whilst not having to have the car in bits. These can be really expensive brand new nearing like £300 for one arm. Here is the Arm being painted, all the Rust was removed, it was then Primed and painted Black, once set the Mating surfaces for the bolts were then cleaned up to look original. Finally The Fuel tank. At first i was thinking of buying a new one but it turned out that the one i had was not that bad in the end. when i took it off the car it looked very corroded but after cleaning it, it came up well. I also noticed the fuel pump was also covered in that same underseal used on the underside of the car its a bit of a blessing and a curse as its protected the fuel pump really well, however it was an utter pain in the backside to clean up. Still even had the Original Bosch sticker on it underneath lmao For the fuel tank i wanted to remove all the rust and then stonechip it to protect it from further road exposure. So i went out and got some generic Hammerite stone chip to do the job. I was pretty chuffed with how it came out, a nice smooth finish, which was what i was after. I did put it on thick in some areas mainly around the edges and the lip of the tank to prevent any rust from creeping in. I finally after many hours got the pump stripped down and cleaned up. surprisingly it came up really well not as much rust as i thought there would be either. I didn't get many photos of the process between this and fitting it all back as it was getting dark and i just wanted to get the thing done. I painted the top of the fuel pump with some brush on hammerite black as it was the only thing i had lying around at the time, the finish could have been better but to be honest its gonna be under the car and covered up so its not exactly in view and it will just protect it from rusting out. But there we go, all refurbished with new clamps and nuts, all cleaned up and painted. Im pretty pleased with the outcome of this. Just need to get round to doing the Straps next and fitting the pads back on I managed to get the straps done today also. They were pretty rusty at the ends however, they weren't horrendous. So i removed all the rust/paint/underseal and got them back to bare metal to be etch primed. Once that had set i then put the Satin Black paint on. I managed to find some Rover parts to use at the mounting end as the old ones had seen better days. i found some brand new mounting bolts for £10 which wasn't bad at all. Unfortunately a lot of the Honda stuff isn't available and when you think it is, its usually listed wrong and is actually for the EK / EG Civics. Not a bad thing as you don't have to pay for the Honda Tax Here are some Before and After photos, i think these will finish off the Fuel Tank Assembly quite nicely. It saves me buying new fuel straps too as they aren't cheap either.

thanks man for your help!! i will look into it :)