Leaderboard

Hi everyone, Thought I'd write up a post to help a few people out. Spent 2 hours researching this today. It is possible to fit after market seats in an MB model civic without a tailored/specially fitted subframe. So for all of those that would like a sportier seat, or some racing seats, this is how you do it and what you need List of parts: Seat (of your choice) Universal side mount rails Base mount conversion rails (you will only need these if you are buying seats with base mount/bottom fitting only) How to install seat seat: Remover factory seats and rails from car Remove factory rails from factory seat install universal side mounts to factory rails ( some bolts may need to be removed or cut off) put factory rails back into car with universal mounts attached Install base mount conversion brackets to side mounts install seat to base mount bracket If you have a seat that is side mounts only you will not need the base mount conversion bracket. you can skip step 4 and install the seat directly to the universal side mounts. The great thing about the universal side mounts is that you have a lot of choice in how you can position your seat. meaning you can have more lean in the seat. be higher up or lower down. this is all depend ending on the side mounts you buy and the amount of holes available. List of parts and seats I used to make this possible: Seat - Sparco R100 - https://www.demon-tweeks.com/uk/sparco-r100-seat-7000253/ Side Mounts - Sparco Steel Side Mounts - https://www.demon-tweeks.com/uk/sparco-steel-side-mounts-s-s004902/ Base mount conversion - OMP Base Mount Conversion Brackets - https://www.demon-tweeks.com/uk/omp-base-mount-conversion-brackets-omphc0-0660/ Hope this helps anyone still trying to figure out how to do this.

Whoops, hope these work haha. Got round to fitting most the parts - also fitted a k-tuned rep short shifter with a stainless weighted knob which makes the car feel so nice to drive - will get a photo soon. Me and my wife have also had a baby so time and money to work on the car are in short supply!! Next steps are to get the interior sorted - really want to fix the headliner, and seeing Kaleverada's thread has me inspired for the pillars! Also really want to strip out the back, tint the windows & fit bucket seats...

So, did a good bit of work to the car again. This time I installed a proper mounting bracket for the cold air intake as the old hacked-off and jury-rigged intake mani bracket looked pretty bad, to be honest. Also installed a pair of much more serious sounding horns than that little beeper that the car came with. They sound a lot better than the OEM one did, and are quite a bit louder on top! After that I installed a set of new bumper screws - the original ones were completely rusted and cruddy, and one almost stripped completely when I took that bumper off! Then I got to work on my seat-project. As I said in my last post - the original seats make me sit a bit too high for my own tastes and I have been looking for either some high-quality (road legal) seat rails for aftermarket seats from either Recaro or some other brand, or a completely different way to sit lower than the original seats would allow me to. As it turns out ... you can fit CRX seats on the original M-chassis rails if you drill out the rivets and fabricate an adaptor plate out of steel (10mm thick in my case). I got lucky a few years ago and managed to take a pair of these seats off a guy for jsut 250 bucks total. :) Here's how the first prototype looks like: This was only to take a look and see if my idea could even work to begin with, and if it would make me sit lower than the OEM seats would, but as luck would have it ... this combo works flawlessly and I sit about 5 to 8 centimetres lower than I do in the stock seats! :D They are also quite a bit more comfortable, if a bit worn-out. Real plushy. :) But as things stand right now I'll just make a few more refinements to my adaptor brackets, give those seats a thorough cleaning session and maybe add some more side bolstering to give them a bit more of a sporty feel and I've got myself a nice pair of OEM Honda seats that do exactly what I want from them! :D

So, a few boxes full of fun-parts arrived yesterday... :D I'm still trying to find a good machining shop to get a port and polish, a valve-job and to get the rotating assembly properly balanced, but things are slowly progressing on the new engine build. It's going to be unconventional for sure, but I'm going to be fully building an N/A D16Z6 that I've bought for this project. Forged conrods, high compression pistons, stage 2 camshaft, lightened flywheel, the whole nine yards. I've also done some test-fitting already and it seems that the 'LITE'-series of conrods from Skunk2 doesn't require any notching of the block to fit, which is a huge win in my book! Though I had to cobble together a pseudo-piston from a few pieces of plastic and foam for the test-fit, as the pistons I bought are .5mm oversize and I haven't had the block bored out yet. Worked super well, though! But I'm super stoked to see what kind of power gain this is going to get me, and especially how high I'll be able to rev it. Components-wise it should be fine up to 9.000 or even 10.000 RPM, but we all know that it probably won't make much or even any power up that high in the rev-range. Based on my research into other all-motor D16 builds and B20 builds I'm confident that it should definitely hold up to 9.000 relatively comfortably, as many people in the states rev their stock-rod B20s that high without much issue, running only ARP rod-bolts and nothing else. (B20 engines have the same stroke as D16s, btw) It's going to be a while until things get moving properly, but the first step has been taken and all that's holding me back right now is finding that machining shop! :D Some folks are probably going to ask why I would take a D16 that far instead of just going B-Series, and I'm going to answer that by telling you that a B-Series swap costs around four to five thousand Euros where I live. If you can even find one... That's a lot of money for just a stock engine and trans. And it's also why I'm going to spend about the same amount of money to build a D-Series that is going to make roughly the same power, as well. I simply want a built engine. Simple as that. I've always wanted to build a proper all-motor engine and I finally got the chance, both time- and money-wise to do so, and I'm going to do it! :D I've also been doing some research into getting a road-legal bucket seat, or any kind of seat to be honest, because the stock seats are just too high for my tastes and I constantly have to lean forward when I'm stopped at a red light. Someone else on this forum already made an extremely helpful post about the seat rails from Planted Technology, which helped me immensely, but I've also found a local engineering company here in Germany which is able to fabricate everything in-house and even get it entered into the car's paperwork the legitimate way. That comes with its price though... Well, anyways. That's the current state of my project. See ya 'round!

Sensor for the ir remote I believe.

Finally got around to installing my Hondata and let's just say that I might have been a little nervous when I turned that ignition key for the first time, hah! But everything went well, and I now have a running, chipped D16Z9 engine, woohoo! It might be running richer than Jeff Bezos at a marathon for now, but a few good street-tuning sessions are going to take care of that. And I'm talking Lambda-0.8-at-idle-rich; Even a few seconds of cold-start are enough to make the whole courtyard reek of marzipan. Sadly I barely had any seat-time during the past few months, as the bane of every D-Series owner struck - ignition problems. It started as a random ignition stutter (rev-counter visibly took a dip) that quickly ended in a complete engine shut-off on my way home from work, and the car refused to turn back on again for at least five minutes after the initial shut-off. But it weirdly enough acted as if nothing happened when it did decide to work again. Spent a few weeks hunting down the issue, buying a new igniter, new coil, the whole nine yards, but the issue persisted. I suspected that the sensors inside of the dizzy might be the problem and looked up part numbers, but quickly found out that those are not sold separately. Dang it. That's when I went "F*k it, I'm gonna buy a whole damn new distributor." But, as it turns out, 99.9% of aftermarket dizzys for D-Series are hot garbage and people always have to buy new ones as they break down faster than you can say K-Swap. That's chinesium for ya... So I looked at those funny looking "Dragon Fire" -ones, which I admittedly didn't take seriously at first, and through their homepage I found out that they actually meet the IAT standard - Success! If something meets that standard, it's at least not as crappy as all of those cheapo replicas from China. The car has been running fine ever since and even gained a bit of torque down low! :D [A few weeks later...] Last weekend it was finally time for yet another small addition, as I finally grew tired of the original pedals and imported myself these beauties straight from the land of the rising sun. The instructions might be slightly difficult to read, but at least they included some pictures. And, well, installing pedals is kind of self-explanatory, y'know? Quick peek at them, straight out of the box. The installation process is actually super easy, as taking off the OEM accelerator-plastic is the most difficult step in my opinion. But with a small-ish flathead screwdriver and a little bit of convincing you can lift the plastic nose on the top and then just slide it off! After that, simply remove the plastic strips from the double-sided adhesive, set the covers in place and attach the small metal clamps that screw through the pedal covers to sandwich the pedal between the little clamps and the covers. This is what the finished product looks like. :) The clutch and brake pedal have that extremely grippy texture to them, which looks to be some kind of metal foam that has been injected into the frame. (Has even more grip than skateboard-tape!) Oh, and heel-and-toe has gotten a lot easier, as these pedals are a bit fatter than the OEM rubbers. All in all - way too expensive, but worth it. Mmm, take a look at that close-up.

Hey all! New here, although I see alot of posts are quite old, its cool to see people still active on these kinds of forums. I thought it would be a great place for information on potential mods, parts and specs regarding civic aerodecks. I know they are far more popular in the UK. Mine is actually the first one I've ever seen in person here in Ireland.

You can put lowering springs in B6 too. Bilstein told me you can use OEM springs or lowering springs. These shocks can take both. I installed the Eibach springs, and they are much better than the OEM springs. You can feel that the suspension works much better with the Eibach springs; I even find it more comfortable than the OEM ones, but I think it lowered a little more than I wanted in the front. At the back, it is very good. I have a friend with an EG Coupe with B8 and Eibach, and I feel it is more arsh compared to mine. I'm of the opinion that you shouldn't put EG stuff on MB when there are MB parts available because something has to change in that particular part; otherwise, they are both the same references. Don't use EK springs because the weight ratings are totally different. The spring plate is indeed a little bit small, but I have been running it for two years without a single problem. On the subject of brake lines, I have had mine secured by zip ties for almost two years without a single issue. Now I need to buy a front camber kit because the camber is at -2 degrees. This camber is a tire killer. I leave a picture of my Aerodeck with Bilstein B6 + Eibach Springs.

Got round to fitting the MG spoiler I got from Craig on here. Quick lick of plastidip and looks the part I reckon

Looks sweet that man! Some of the vibration you mentioned could be from the stiffer or solid bushes you’ve fitted, quite a lot of gearbox vibration gets transmitted through those. Either that or whilst in gear the shifter actually sits on top of the the exhaust, I know when I had mine adjusted to as low as it went, so the shortest possible throw, it’s would knock into the exhaust. Have a completely different setup now but the Hybrid Racing one does looks good man! Well done

Bay shot because why not. Changed whale d**k out to actual carbon fibre one, and changed rocker cover to a fake Mugen one. Looking a lot tidier under there now!

Coming along nicely mate! I'm deffo replacing DDs "meep-meep" horn too, looking at maybevfittjng one from a MINI of all things as they're quite beefy!

Hello, I've just got my Honda Civic Aerodeck 1.6LS import from Italy. I would like to know how much power steering fluid and brake fluid i have to buy so my mechanic can change them fully(steering fluid and the clutch and braking fluid).

That blue looks stunning! Loving the car in its latest form mate!

Good afternoon everyone,I’ve just joined (just found your wonderful site) and just to say I own a 1996 civic MA 5 door hatch.(had an MB before) and has the dreaded headlining that has dropped. it’s mot is today ? , but wanted some advice please if that is ok. I would like the following and where is best to buy from, pair of rear light units (orange indicator ones) can you buy new or eBay ? pair of rear hatch struts eBay or someone like struts depot or somewhere else. passenger door mirror (electric unpainted black one). the only other issue is rear wiper washer isn’t working ( washer motor is working and a dribble came out but nothing now) I appreciate any help offered. thanks Gary.

Ahh man, sorry it didn't work out with the Crown mate. Truely nice car but like you say, expensive in every way. Had a feeling you would get pangs about the mb6 mate. the amount of time, work and money you poured into it, plus how long you had it, was always gonna be a tinge of regret selling her. Know I felt physically sick after |I sold Ruby the first time, even more so when I saw what the muppet that bought her was doing to her! Wasn't as bad the 2nd time I sold her although still miss her even now. Glad you're back in a Honda though! I have mixed feelings over the FN2's but mostly good feelings! I love the styling more than I think any car I've owned (except my Mk3 Cortina's though!), just think they look so cool from any angle! Also best interior I've had by far! Only things I didn't like about the TypeR FN2 were the fuel consumption and the ride. Just far too stiff for me! Power was nice though but deffo was gonna loose my license if I'd kept Roxy! If I'm honest, think I prefered my FN1 typeS, as a daily anyways. But loved them both, just something about the FN Civics. Even now I'm still looking at them on autotrader! Deffo get a new project thread going for the Fn mate, would love to see where you go with it!

Hey,.. erm yeah I did some more mods on the crown and got it all set up beautifully. Put some lovely 4 pot brakes on etc. then got a bit twitchy with it because everything is so expensive for those cars. Realised was gonna take 10k minimum really before I'd be remotely happy with performance etc, so I'd be into it for over 20k by that point. And also I drive so Infrequently when I do go out I want something fun to drive , which nice as it was, it wasn't a fun car. So sold it. Genuinely gutted I sold my mb6 actually. Moment of madness. So been in a bit of a rut and a bit grumpy about cars. But have baught an fnPoo with some nice mods on. And plan to put my stamp on that and do some track days etc next year.

Hi all, So I can confirm aftermarket seats, without cutting frames or welding mounts to car, are completely possible. If you have read my before method with the universal frames this way is a lot easier and more cost effective. After 3 months of research I found a company called Planted Technology, they produced made to order seat sub frames for many cars. I emailed them to ensure my car was not an EK or an EG. I measured up the cars holes and got back the details of the closest fit frames they make. The Honda Accord 4th & 5th gen have the same interior as the MB3/MB6. I took a risk bought the frames and they do in fact directly fit. I admit it was a bit of a fiddle as they had to come from America so may have been slightly warped or bent on delivery, never the less I got them in as seen in the image below Here is a link to the main page, it would better off ordering them from GSM performance Planted Technology https://www.plantedtechnology.com/products/planted-seat-bracket-honda-accord-4th-5th-generation-1989-1997-passenger-right GSM performance https://www.sportseats4u.co.uk/product/planted-honda-accord-bracket/ Things to consider, these frames do not come with threads. M12 Nuts will be needed to fit seatbelts, M8 Nuts and bolts to fit seats to rails or frames, washers highly recommended

Hi guys. We've just added a new feature to the forum, Popular Contributors. You should see a box at the bottom of the home page (depending on the device you are using) which shows our most popular contributors. You can change it from week to month and year. If you click on the "see more" this will give a full list of contributors. Don't see your name on it? Get posting! We love to hear from you, even if it's just a small update on your cars projet thread or posting a pic of your car. Have look through the different sections of the forum and see if there's maybe a question been asked that you can help with. Most of all, enjoy the forum. It's your club and site!

Wrapped the front bit behind plate today

Hello everyone, I’d like to share with you all, a purchase I’ve done via Facebook marketplace, of some OEM Honda MB/MC headlight covers. Bought them from Anthony Vickers, super nice dude who isn’t a scam like you see very often these days. Covers were packed very good so no damage at transport from the UK to the Netherlands thank god! Really stoked about these as you never see them! I like rare stuff so these will look nice in the collection for the car! Cheers!

Those headlights look amazing! Nicest conversion I've seen done to them. Headlight covers really do finish it of nicely, nice mix of retromod and OEM. Whole cars is looking superb mate, one of my fav members cars! Looks flawless.

First event today with the Aerodeck and my new retrofit headlights with the headlight covers on, imo they just finish the look of the car! Really stoked with the looks now

Just to show this, was just looking for some new bungs for my spare wheel well as a couple of mine have gone a bit gummy... https://www.parts-honda.uk/honda-cars/assignment_spare_parts/82871671000 £4.52 ex VAT from honda https://rimmerbros.com/Item--i-BNP4028 60p ex VAT for rover.. Quite a difference if you're buying the 10 that honda has as the default number for replacing them all!

Really nice post! Will use this in the future :)

So Today i have sorted out the boot floor finally, as it was starting to get on my nerves a bit. but its all welded, seam sealed and painted. alongside the refitting of the tow eye reinforcer. i also jacked it up to see if it would break, it didnt! which is great. Later on i started to work on the passenger side sill, i have cut away an area to gain access to the lower section, this will then be cut further out when i fit the new upper piece in. I will be fabricating new reinforcer panels, perhaps a new jacking point panel and the panel that joins the sill to the arch. Ive cut the area out of the arch out as i have a New old Stock panel to go in place, i also have a fabricated lower sill that i made earlier on in the year which will be getting cut to size to be butt welded in. I have also done some very quick fitments just to get an idea of the final work, although there is still some more cutting and grinding to do before everything fits in perfect. hopefully that will be all done tomorrow.

Lol 😂 you'll be fine mate, they're really strong. Ours have been on for the past 15 years or so and are still like new.

This is the colour the car be going soon. Nissan gtr bayside blue

Got hold of a saloon lip kit got the front primed and test fitted I have since realised the rear is different so maybe need to extent it it just let someone else have it

Good idea to keep your ring clean mate I'll get me coat...

Ahh mate! The mats are lovely. Like arctic camo OEM s**gpiles! Very random. Yes can do double din where the cd player and cassette lives under the big flap at the bottom. Of course cam get large android screens like i have in the alphard too. When money allows ill look into something for it. Until then its got 3 prodigy albums in it. Took a few snaps tonight.

So an Update on the Lower Sills I Managed to cut them out the other day, i got all the pieces i needed to create the sections that are required. As shown i used the existing cutout to get the shape of the sill, for the Rear Extension piece and also the mid section The welding course that i was doing said that we are able to do a project in the last lesson, so i used this time to start bending the metal to the profile that i need for the lower sill. This saved me buying a Metal bender that fit the requirements for the job as i needed one that was capable of bending 1.5mm steel and the length had to be 1200mm or more for the mid section if i was to buy one like that youre looking at £1000+ for a decent one that will last you. So here are some images to show the final product really chuffed with how they have turned out, they do require an ever so slight bit of fettling to get right as the profile of the back part actually isn't straight however it comes in at an angle then straightens out when it gets to the wheel arch There are a few other little panels that i still need to fabricate such as the panel that joins the wheel arch to the sill and also the jacking point reinforcer that sits inside the sill. These will all be made in due time. I then offered it up to an existing panel to see how well it fits into place, and to be honest i was surprised how well it did! After all the Testing of fitments and other things i thought nows the time to get them protected so they dont rust. I keyed the surface and made sure that the panels were clean from dirt, rust and residues and then used some Bilt Hamber Electrox Zinc primer. Coated them twice to make sure there is a good layer of protection. Overall im chuffed with the outcome, who knows i may end up getting a Metal bending machine and start making repair panels for these cars lmao certainly ideal as a lot of the panels that are out there for these cars aren't the best.

Cheers Guys, Im hoping After june i can start actually doing the welding, i have Been doing this course and ive been doing some practising, Did some MIG tonight which is what ill be using, Surprised to say for my first time i didn't do too bad managed to create some decent tacks and i also created a few lines of weld alongside creating a box! so a few more months of practising for confidence and we should be good. They also said that i can actually create the Inner sill there using the Metal Folding machine they have so i am pretty pleased to say the least! I will post some photos once the sill has been fabricated to show you!

Toyota Crown is an amazing car, loaded with kit and the ultimate cruise mobile. Can look so sweet modded too.

Totally agree, should feel really proud mate. So sad to see her sold but do get it. You'd taken her as far as you can power wise (more than once lol) and have owned her a long time so natural that you need something different. Really really hope we see her back in the club though, my favourite vtis ever that! Is the new owner joining you think?

HONDA CIVIC 'M' SERIES COMPATIBILITY DATABASE Civic5 accepts no responsibility for any inaccuracies or omissions from this database and all that STEERING AND SUSPENSION COMPONENTS *Wheel and tyre info....Stock ET is 45 for all M's (widest recommended rim with this et is 6.5" at r15? ). DC2 alloys need spacers to fit over 282 calipers *Springs and shock absorbers....Same as dc2/eg/ek/ej/400/45/zs. DC2 coilovers will need the Integra LCA. Matched springs and shocks are specific to the weight of the model so Aerodeck are different as are other civics or Integras. *Front upper wishbone....Same as dc2/eg/400/45/zs. EK is different the bushes are pressed into the arm. *Front lower wishbone....Same as dc2/eg/ek/ej/400/45/zs *Front hub carrier and balljoints....Same as dc2/eg/ek/ej/400/45/zs *Hubs....All M's use 4 x100 pcd hubs from contemporary civics except the MB6 which uses 4 x 114.3 (4.5") pcd hubs from the Integra and Prelude. *Front ARB....Same as dc2/eg/ek/ej/400/45/zs. To upgrade arb size you will need to change the body mounting bushes *Rear ARB....Same as dc2/eg/ek/ej/400/45/zs. To upgrade arb size you will need to change the body mounting bushes. *Front suspension bushings....Same as dc2/eg/ek/ej/400/45/zs *Track rod ends....Same as 45/400/zs *Steering rack...Same as 45/400 *PAS pump...Non Honda engined Rovers use flexible hosing (mounted on right of engine) *Rear trailing arm....Same as dc2/eg/ek/ej/400/45/zs. Drum versions can not be converted to disc. *Rear upper control arm....Same as dc2/eg/ek/ej/400/45/zs *Rear lower control arm....Same as dc2/eg/ej/400/45/zs. Some LCA's do not have a mounting for an ARB. *Rear toe adjuster....Same as dc2/eg/ek/ej/400/45/zs *Trailing arm (compliance) bush....Same as dc2/eg/ek/ej/400/45/zs *Rear suspension bushes....Same as dc2/eg/ek/ej/400/45/zs BODY PANELS AND LIGHTS *Front bumper....All different, to change MA to MB you also need to change bonnet (and front crossmember?) MB6 front lips will not fit the MA without modification. *Rear bumper....MB will fit MA *Sideskirts........MA/MB/45/400/ZS all fit the same mounting points. Vti-s and ZS180 having variations in style. *Front wings....All different *Bonnet....All different. *Bonnet catch and struts....MA/MB/45/400/ZS all same. Catch lever varies on MA. *Scuttle cover....MA/MB/45/400/ZS all same *Windscreen....MA/MB/45/400/ZS all same *Door glass.... MA/MB/45/400/ZS all same *Tailgate....MA/MB same apart from number plate surround. *Tailgate catch and struts....MA/MB/45/400/ZS all same, all standard struts will take the weight of the standard vti spoiler. *Doors.... MA/MB/45/400/ZS all same *Headlights.... MA/MB slightly different outer shape. There are no aftermarket headlights. *Taillights....MB fit MA, MB have clear indicators, MA amber. *Side repeaters.... MA/MB/45/400/ZS all same *Fog lights....MA and MB have slightly different surrounds? *Wing mirrors.... MA/MB/45/400/ZS all fit same, some electric, some manual *Sunroof.... MA/MB/45/400/ZS same. *Handles and other trim pieces.... MA/MB/45/400/ZS same apart from number plate surrounds/ rear light trims. INTERIOR *Front seats and rails....MA/MB/400/45/ZS same fitting. Other Honda seats will need modification to the rails. *Rear seats and rails....MA/MB same ZS will not fit. *Centre console....MA/MB/400/45/ZS same fitting. Some models have a centre arm rest that fits all M's *Dashboard....MA/MB/400/45/ZS same fitting. The MB6 vti-s has carbon dash inserts. *Steering wheel....MA/MB same MB6 has leather finish. Rover will fit but are trispoke so you will not be able to get rid of the Rover airbag and logo. (DC2 will fit with modification?) *Steering column....MA/MB/400/45/ZS same *Switches etc....MA/MB/400/45/ZS same *Instrument cluster....MA/MB/400/45 same. (ZS 180 and MB6 have different tacho's?) *Door cards....MA/MB/400/45/ZS same *Pillar trims....MA/MB/400/45/ZS same *Headlining....MA/MB/400/45/ZS same *Rear mirror....MA/MB/400/45/ZS same *Parcel shelf....MA/MB *Audio components....MA/MB/400/45/ZS same. The MB6 and some Rovers have better speakers and door tweeters that fit all M's. BRAKING COMPONENTS *Front discs....262 except MB6 which uses the 282 system. Some companies make 282 rotors to fit 4x 100 hubs (generally as an upgrade to EG civics) *Rear discs/drums *Front calipers....Single pot lucas 262 system. Same as 400/45/ZS/EG/EK. 282 for MB6. *Rear calipers....Same as 400/45/ZS/EG/EK/EJ. *Master cylinder....Same as 400/45/ZS/EG/EK/EJ.(?) Does the 'teg use this too? *Brake fluid.... *Brake hoses....Same as 400/45/ZS/EG/EK. Drum and disc versions are different. *Rear Disc backing plates part numbers. SMD000080  SMD000090 From RimmerBros (order for MGZS) Just checked still showing in stock around 25 each (as of 21/3/2020)  ECU AND ELECTRICAL OBD Loom/ aftermarket wiring Lamda IACV FIT VTEC controlers Fuses and resistors Battery Alternator D SERIES ENGINES- D14A2, D14A4, D14A3 (EDM), D14A8, D15Z1, D15Z8, D16B2, D16Y5. Engine mounts Sparkplugs Engine oil Oil filter Fuel filter Distributer HT leads Valves and valvetrain parts Cam Cambelt Cam gears Crank Pistons Con rods Intake Throttle body Intake manifold Radiator Fan Thermostat Coolant FI info B SERIES ENGINES- B18C4 Same sort of stuff TRANSMISSION COMPONENTS Shifter UJ Shift rod Extension rod Shift bushings Clutch Master cylinder Reservoir Release cylinder Gearbox Gearbox oil Driveshafts EXHAUST COMPONENTS Manifold....B and D series engines use a slightly different manifold Cat section....UKDM cat (different length from the JDM cat) Mid section....MA/MB all same (?) do rover fit? Backbox....MA/MB all same except Aerodeck which has a longer tail (?) There's probably a lot I've missed off, might be best to improve it as we fill out the list? We probably ought to have glossary for terms (stuff like DC2, EG, ITR, IM, PCD) to make it accessible for noobs and non Honda geeks