Jump to content

noodels

Civic5 Supporter
 View Profile  See their activity

  • Posts

    4,657

  • Joined

  • Last visited

  • Days Won

    24

 Content Type 

Everything posted by noodels

  1. noodels
    I would go by the serial numbers on it,S80*********? to be sure google will find correct numbers as I don't know of hand also plenty of f**ked ones so be very sure and try it if possible in car they are a weak gearbox and prone to problems. good luck
  2. noodels

    What the?

    noodels replied to dr_broon's topic in Chat Lounge

  3. noodels

    Mounts

    noodels replied to dogg1210's topic in Engine & Chassis

    Share your results when you do yours
  4. noodels

    Mounts

    noodels replied to dogg1210's topic in Engine & Chassis

    Need to take both front torque mounts off to do rear mounting,that gives the movement and room . read that after failing to do mine
  5. noodels

    Mounts

    noodels replied to dogg1210's topic in Engine & Chassis

    Thanks for JSP heads up
  6. noodels
    157.8mph given 254kph reads 3.9% high on 195/50/15 s so about 6-8mph,so about right on speedo
  7. noodels
    They done a 1000 HP drag civic
  8. noodels
    Just tune the C4 with a good exhaust manifold and exhaust system + breathing mods.185HP <An inlet+cams+head that needs ecu and Mapping > £1200++ there alone 200HP Or just use an R engine=Job done already 200HP C4 is not the right cylinder head for the R piston design,the squish is wrong Google Frankenstein Honda B series
  9. noodels
    There you go
  10. noodels
    Not sure but worth checking if the gear linkage is compatable
  11. noodels
    http://www.isitaboat.co.uk/cars/honda_civic_type_r__ek9_/
  12. noodels
    http://www.ff-squad.com/tech/temp/pistons.htm
  13. noodels
    Remove battery and clean leaves out from there, there is a rubber grommet containing wiring harness, water runs into this and then too ecu area. Maybe different for lhd car though ?
  14. noodels
    Also Check the earth, one on the stat clean that up. dizzys have a few probs also Throttle position sensor TPS IACV FPR
  15. noodels
    Congrads
  16. noodels
    Snapped ?
  17. noodels
    What should we do with all the money Dave 50/50
  18. noodels
    Swap dizzy to eliminate it is best, make sure its a good one too fuel pump ok ?
  19. noodels
    Grind/cut the welded nut off and put nut and bolt on.
  20. noodels
    10mm divided by 3.142 =3.1mm don't think that would be a problem
  21. noodels
    P72 has a speed limiter as well,so should come in handy
  22. noodels

    Dc2 rack

    noodels replied to shamz's topic in Chassis

    Thought the oil feeds need to be changed as well so need the pipes ect of Dc2 <but could be thinking of Mgzs180 though> but as said same Ratio so no point, smaller wheel is hard work also for car control at speed on the ruff roads, swapped mine out !! could be my tyre/wheel config though..
  23. noodels
    Rear VTIS bumper lower part of an MB6 VTIS does not fit the Aerodeck ..
  24. noodels
    Lights are different size/shape also
  25. noodels

    MB6 Rear wheel bearing

    noodels replied to a question in SOS! Help!!

    ps there was an early Aerodeck -it was not a Civic VTI Aerodeck it was a Accord Aerodeck hence a confusion with Some motor factors.
×
×
  • Create New...